Re: problem with squid (fwd)

Barrett,

Only one machine run at a time. the two machine was not running at the
same time yesterday.

Now, the squid is running and the cache size is up/down between full of
100% to 96% (or98%).

Only error is "diskHandleWrite: FD 14: disk write error: (32) Broken
pipe" and It is a different problem I think.

Regards

Julie

On Wed, 29 Jul 1998, B. Richardson wrote:

>
> Are two machines sharing the disk the cache is on?
>
> -
>
> Barrett Richardson rabtter@orion.aye.net
>
> On Thu, 30 Jul 1998, Julie Xu wrote:
>
> > Markus,
> >
> > After I did kill -HUP squidid, it is wring fine until now ( about 12
> > hours). I still keep looking at it. Hope no problem occured again.
> >
> > >From start, I have not change any configuration. But our all the squid
> > software and caches on the disk shared by other machine. I had stopped
> > the squid run in original machine and started it on another machine. When
> > the original machine running, I had restart squid on original one again.
> > ( of course, I stop the other machine first ). Than the problem are
> > occurring all the time through yesterday. I don't know about today.
> >
> > I have to say it is a very painful to remove all the cache out and
> > restart again. Do I have any choice alse?
> >
> > Best regards
> >
> > Julie
> >
> > On Wed, 29 Jul 1998, Markus Stumpf wrote:
> >
> > > On Wed, Jul 29, 1998 at 04:38:17PM +1100, Julie Xu wrote:
> > > > Michael and experts,
> > > >
> > > > Bad new again, from cache.log I start to get message as below:
> > > >
> > > > 98/07/29 16:22:06| WARNING: Repeated failures to free up disk space!
> > > > 98/07/29 16:22:06| storeGetSwapSpace: Disk usage is over high water mark
> > > > 98/07/29 16:22:06| --> store_swap_high = 72181 KB
> > > > 98/07/29 16:22:06| --> store_swap_size = 268241 KB
> > > > 98/07/29 16:22:06| --> asking for 0 KB
> > > >
> > > > this message come out every minutes.
> > > >
> > > > now the cache is not full
> > > > sp3#df /cache
> > > > Filesystem 512-blocks Free %Used Iused %Iused Mounted on
> > > > sp1:/cache 1458176 727472 51% - - /cache
> > > >
> > > >
> > > > What is problem again???
> > >
> > > Ok, from the beginning:
> > >
> > > squid-1.1.x has a kind of "database" where it stores all the information
> > > about it's objects. This database is kept for one in memory and for
> > > two on disk. The latter is the file "log". When u send a kill -USR1 to
> > > squid, it dumps it's memory database.
> > > While squid is running it appends new fetched objects simply to the end
> > > of "log".
> > > If squid dies without a chance to write the clean "log" file it reads
> > > the "unclean" one and verifies it against the content of the cache
> > > directory(s). This is "slow startup".
> > > If it has a clean log file at startup (in this case it has a file
> > > "log-last-clean") it simply reads the file and no checks against
> > > the cache directories are done.
> > > In both cases it maintains a file "low.new" during startup and when
> > > it is finished it removes the "log" and renames "log.new" to log.
> > >
> > > The worst case that can happen to squid-1.1.x is that it loses the
> > > "log" file and has no chance to dump a clean new one.
> > > Then it doesn;t have any information on the content of the cache
> > > directories and all the objects are still there but squid is "blind"
> > > for them. This behaviour is fixed in 1.2.x
> > > In this situation you are probably running into a situation where
> > > your disk is physically full, but squid doesn't "know" about it.
> > > The clean way is to remove all the cache files/directories and
> > > "start over".
> > >
> > > The situation you have is very strange.
> > > Did you change something in the squid.conf? Maybe change the user
> > > squid is running under? In this case squid might not be able to
> > > unlink already existing (and outdated) files in the cache.
> > > >From the messages you receive I assume the latter in conjunction
> > > with a modification of the squid.conf file giving it less disk space
> > > to use.
> > > Squid does not simply "fill the disk until it's full" but you have
> > > to configure the amount of disk space squid may use.
> > >
> > > Hope that helps
> > >
> > > \Maex
> > >
> >
> >
>
>
Received on Wed Jul 29 1998 - 20:29:38 MDT