RE: [squid-users] Re: Kerberos Authentication - Squid 3.1.0.13

Long over-due but I finally got past my error with this. Thanks to all who
responded, basically you were dead on, I just had to download the SDK CD
(Disk 1) and install a few packages:

-installing libcom_err-devel for krb5-devel (from SDK CD 1)
        /mnt/cdrom/suse/x86_64/libcom_err-devel-1.41.1-13.9.x86_64.rpm
        /mnt/cdrom/suse/x86_64/libcom_err-devel-32bit-1.41.1-13.9.x86_64.rpm
-installing keyutils-devel for krb5-devl (from SDK CD 1)
        /mnt/cdrom/suse/x86_64/keyutils-devel-1.2-107.22.x86_64.rpm
-installing krb5-devel (from SDK CD 1)
        /mnt/cdrom/suse/x86_64/krb5-devel-1.6.3-133.10.x86_64.rpm
        /mnt/cdrom/suse/x86_64/krb5-devel-32bit-1.6.3-133.10.x86_64.rpm

Thanks all. Now that I have the EASY part out of the way, time to dig into
the authentication /wrist! =D

-----Original Message-----
From: Daniel [mailto:Squid_at_ZoomEmail.com]
Sent: Friday, August 14, 2009 4:22 PM
To: 'Markus Moeller'; squid-users_at_squid-cache.org
Subject: RE: [squid-users] Re: Kerberos Authentication - Squid 3.1.0.13

Markus,

        First, please correct me if I'm wrong but I looked for 'gssapi.h' in
config.log and I'm assuming that config.log contains all the log information
from doing a /configure? Assuming that I am correct, I couldn't find
'gssapi' anywhere inside the log file so I'm not sure if that's a good thing
or a bad thing.

I went ahead and dumped the output of the ./configure to a file and these
are the only lines that I could find for gssapi.h:

checking gssapi.h usability... no
checking gssapi.h presence... no
checking for gssapi.h... no
checking gssapi/gssapi.h usability... no
checking gssapi/gssapi.h presence... no
checking for gssapi/gssapi.h... no

If there's anything else that I could try, I'd greatly appreciate it.
Thanks!

-----Original Message-----
From: news [mailto:news_at_ger.gmane.org] On Behalf Of Markus Moeller
Sent: Tuesday, August 11, 2009 3:25 PM
To: squid-users_at_squid-cache.org
Subject: [squid-users] Re: Kerberos Authentication - Squid 3.1.0.13

Hi Daniel,

 Did you see any configure errors for gssapi.h ?

Markus

"Daniel" <Squid_at_ZoomEmail.com> wrote in message
news:001301ca19fe$9f450a50$ddcf1ef0$@com...
Good afternoon,

In my attempt to get Squid on our SLES 11 box authenticating with
Kerberos (negotiate), I used the following to re-configure:

./configure --prefix=/usr/local/squid --enable-cachemgr-hostname=sclthdq01w
--enable-auth="negotiate" --enable-negotiate-auth-helpers="squid_kerb_auth"

The "configure" appears to run without any issues. However, upon running
"make all" I receive the following errors:

squid_kerb_auth.c:507: error: implicit declaration of function
âgss_display_nameâ
make[5]: *** [squid_kerb_auth.o] Error 1
make[5]: Leaving directory
`/tmp/squid-3.1.0.13/helpers/negotiate_auth/squid_kerb_auth'
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory
`/tmp/squid-3.1.0.13/helpers/negotiate_auth/squid_kerb_auth'
make[3]: *** [all] Error 2
make[3]: Leaving directory
`/tmp/squid-3.1.0.13/helpers/negotiate_auth/squid_kerb_auth'
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory
`/tmp/squid-3.1.0.13/helpers/negotiate_auth'
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory `/tmp/squid-3.1.0.13/helpers'
make: *** [all-recursive] Error 1

Any ideas?? As always, T.I.A.

-Daniel
Received on Wed Sep 09 2009 - 20:51:51 MDT